Find the Parts you need for Aerodry and Worldwide Drying Systems.

Stainless Steel Junction Box

  • Non-corrosive 304 Stainless Steel
  • 4 inch wide x 6 inch tall x 5 inch deep
  • 1 inch NPT 304 SS connection
  • Custom Hoffman brand build
  • NEMA 13, IP 66
  • UL Listed, CSA Certified, IEC, cUL
  • Only NEW, tested components, proven suitable for harsh wash conditions, are installed in Aerodry systems and provided as replacements

Carwash Dryer Side Nozzles

  • Soft, non-marking Silicone
  • 6″ ID reducing to 4″ ID at exit
  • 20″ overall length
  • Includes worm gear clamp
  • Colors: Red, blue, or black
  • Only NEW, tested components, proven suitable for harsh wash conditions, are installed in Aerodry systems and provided as replacements.

Carwash Blower Top Nozzles

  • Soft, non-marking Silicone
  • 12″ ID reducing to 10″ ID at exit
  • 18″ overall length
  • Includes worm gear clamps
  • Colors: Red, blue, or black
  • Only NEW, tested components, proven suitable for harsh wash conditions, are installed in Aerodry systems and provided as replacements.

Car Wash Dryer Motors

  • ABB/Baldor, 15 HP, 3 phase, 60 Hz
  • Baldor Specification #07K090W360G1
  • ABB (11 KW) Specification #07K090W360G2
  • Premium Efficiency Motors Available
  • 3600 RPM, 254TZ frame, 1.15 SF
  • Stock 230-460v, useable @ 208v or 575v
  • TEAO (totally enclosed, air over), no grease zerks!
  • Cast body dissipates heat
  • Oversize bearings increase motor life
  • Factory extended leads reach exterior J-Box

* New bushing may be required to secure fan to shaft of replacement motor.
*Guaranteed operable on variable frequency drives (VFDs or VSDs).
*Other voltage/Hz combinations available.
*Only NEW, tested components, proven suitable for harsh wash conditions, are installed in Aerodry systems and provided as replacements.

Taperloc Bushing

  • Secures fan to motor shaft
  • For 1-5/8″ motor shaft
  • Screw size M8
  • Hex key size 6mm
  • Tightening torque 30 ft-lbs
  • Only NEW, tested components, proven suitable for harsh wash conditions, are installed in Aerodry systems and provided as replacements.

Carwash Air Producer

  • Motor/fan assembly in stainless housing
  • Powered by 15 HP motor
  • Complete, ready for install
  • Replaces Aerodry™ Systems and Worldwide Drying Systems
  • Only NEW, tested components, proven suitable for harsh wash conditions, are installed in Aerodry systems and provided as replacements.

Variable Frequency Drive Panels

  • (various HP/Voltage configurations)
  • Panels include cooling fans with thermostat; exterior hand-off-auto switches for each motor; interface relays (120v and 24v included); individually lockable protection for each drive; main lug power distribution block; stagger-start PLC with timers; thru-door disconnect.
  • Pre-programmed high Hz (operator adjustable).
  • Separate 120v circuit required for cooling function. Enclosure is NEMA 1 painted steel, UL Listed.
  • Fiberglass Enclosures are optional add-on.

Across-the-Line Starter Panels

  • (various HP/Voltage configurations)
  • Panels include exterior hand-off auto switches for each motor; interface relays (120v and 24v included); individually lockable breaker protection for each motor; main lug power distribution block; stagger-start PLC with times; thru-door disconnect.
  • Enclosure is NEMA1 painted steel, UL Listed.
  • Fiberglass Enclosures are optional add-on.